Necesito este Firmware para reparar con UMT el IMEI del telefono, pues no tiene Baseband..
Pudiera servirme tambien un QCN..
Gracias de antemano..
Ocupas alguna version en especial?
Cita de: Jonhy en Agosto 05, 2018, 12:24:35 PM
Ocupas alguna version en especial?
Adroid 6.0.1
Numero Compilacion: Z988V1.3.16
335140B1921Z988V1.5.19.zip 24-05-2018 22:23:19 1,27 GB
339020B2036Z988V1.6.20.zip 24-05-2018 22:23:51 1,27 GB
344090B2116Z988V1.7.21.zip 24-05-2018 22:29:24 1,27 GB
P895A18V1.0.0B18_DL.zip 24-05-2018 22:26:30 1,3 GB
Alguna de esas te sirve??
Cita de: Jonhy en Agosto 05, 2018, 02:19:42 PM
335140B1921Z988V1.5.19.zip 24-05-2018 22:23:19 1,27 GB
339020B2036Z988V1.6.20.zip 24-05-2018 22:23:51 1,27 GB
344090B2116Z988V1.7.21.zip 24-05-2018 22:29:24 1,27 GB
P895A18V1.0.0B18_DL.zip 24-05-2018 22:26:30 1,3 GB
Alguna de esas te sirve??
Cualquiera de esas me sirve..
sobre todo cualquiera de las 3 primeras..
Mañana te lo tengo...
Listo: http://www.gsmarena.com.mx/index.php?topic=1084.0
ZTE Z988 - 335140B1921Z988V1.5.19
Cita de: Jonhy en Agosto 06, 2018, 10:28:58 AM
Listo: http://www.gsmarena.com.mx/index.php?topic=1084.0
ZTE Z988 - 335140B1921Z988V1.5.19
Lo estoy descargando..
espero me sea util..
gracias..
UMT. QcFire v2.6
Operation : Flash
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM6)
Driver Info : ZTE Corporation, zghsser.sys, 5.2104.1.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1209700 [8952] 00000400
OPK_DATA : 46B4EC5C949D2BD3FA853DFEDEE69DF9F6B7415FADA68A0729 345ADC932CB23F
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Firehose Loader...Done
Sending Loader [8952_016.ufl]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8952, eMMC, 16 GB
LU Count : 1 [0x01D5C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Writing [sbl1.mbn] -> [sbl1] ...Done
Writing [ddr.mbn] -> [DDR] ...Failed
Operation Finished.
Module Ver. 2.6
alguna idea al respecto..
Operation : Flash
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM6)
Driver Info : ZTE Corporation, zghsser.sys, 5.2104.1.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1209700 [8952] 00000400
OPK_DATA : 46B4EC5C949D2BD3FA853DFEDEE69DF9F6B7415FADA68A0729345ADC932CB23F
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Firehose Loader...Done
Sending Loader [8952_016.ufl]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8952, eMMC, 16 GB
LU Count : 1 [0x01D5C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Writing [sbl1.mbn] -> [sbl1] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [adspso.bin] -> [dsp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [echarge.img] -> [echarge] ...Done
Writing [emmc_appsboot.mbn] -> [aboot] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [keymaster.mbn] -> [keymaster] ...Done
Writing [system.img] -> [system] ...FailedFailed
Operation Finished.
Ahora desmarcando Protect IMEI / Calibration Data.. llegue hasta aqui..
pero solo enciende en Recovery Mode, no entra en FTM ni EDL.
alguna idea..
Amigo, si es 100% que no entra en FTM y EDL. Solo Jtag con alguna Box como Medusa PRO.
Deseo que alguien tenga algo mejor...