Busco Firmware ZTE Z988 Grand X Max 2

[kpotin]

Necesito este Firmware para reparar con UMT el IMEI del telefono, pues no tiene Baseband..

Pudiera servirme tambien un QCN..

Gracias de antemano..

[Zilre]

Ocupas alguna version en especial?

[kpotin]

Ocupas alguna version en especial?

Adroid 6.0.1

Numero Compilacion: Z988V1.3.16

[Zilre]

335140B1921Z988V1.5.19.zip   24-05-2018 22:23:19    1,27 GB   
339020B2036Z988V1.6.20.zip   24-05-2018 22:23:51    1,27 GB   
344090B2116Z988V1.7.21.zip   24-05-2018 22:29:24    1,27 GB   
P895A18V1.0.0B18_DL.zip           24-05-2018 22:26:30           1,3 GB   

Alguna de esas te sirve??

[kpotin]

335140B1921Z988V1.5.19.zip   24-05-2018 22:23:19    1,27 GB   
339020B2036Z988V1.6.20.zip   24-05-2018 22:23:51    1,27 GB   
344090B2116Z988V1.7.21.zip   24-05-2018 22:29:24    1,27 GB   
P895A18V1.0.0B18_DL.zip           24-05-2018 22:26:30           1,3 GB   

Alguna de esas te sirve??

Cualquiera de esas me sirve..
sobre todo cualquiera de las 3 primeras..

[Zilre]

Mañana te lo tengo...

[kpotin]

Mañana te lo tengo...

Seria Genial..
Gracias..

[Zilre]

Listo: http://www.gsmarena.com.mx/index.php?topic=1084.0


ZTE Z988 - 335140B1921Z988V1.5.19

[kpotin]

Listo: http://www.gsmarena.com.mx/index.php?topic=1084.0


ZTE Z988 - 335140B1921Z988V1.5.19

Lo estoy descargando..
espero me sea util..
gracias..

[kpotin]

UMT. QcFire v2.6

Operation : Flash
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM6)
Driver Info : ZTE Corporation, zghsser.sys, 5.2104.1.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1209700 [8952] 00000400
OPK_DATA : 46B4EC5C949D2BD3FA853DFEDEE69DF9F6B7415FADA68A0729 345ADC932CB23F
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Firehose Loader...Done
Sending Loader [8952_016.ufl]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8952, eMMC, 16 GB
LU Count : 1 [0x01D5C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Writing [sbl1.mbn] -> [sbl1] ...Done
Writing [ddr.mbn] -> [DDR] ...Failed
Operation Finished.
Module Ver. 2.6

alguna idea al respecto..

[kpotin]

Operation   : Flash
Checking for existing devices...Found
Port   : Qualcomm HS-USB QDLoader 9008 (COM6)
Driver Info   : ZTE Corporation, zghsser.sys, 5.2104.1.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID   : E1209700 [8952] 00000400
OPK_DATA   : 46B4EC5C949D2BD3FA853DFEDEE69DF9F6B7415FADA68A0729345ADC932CB23F
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Firehose Loader...Done
Sending Loader [8952_016.ufl]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware   : 8952, eMMC, 16 GB
LU Count   : 1 [0x01D5C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info   : In: 65536 [4096], Out: 1048576, Sector Size: 512
Writing [sbl1.mbn] -> [sbl1] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [hyp.mbn] -> [hyp] ...Done
Writing [adspso.bin] -> [dsp] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [echarge.img] -> [echarge] ...Done
Writing [emmc_appsboot.mbn] -> [aboot] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [keymaster.mbn] -> [keymaster] ...Done
Writing [system.img] -> [system]  ...FailedFailed
Operation Finished.

Ahora desmarcando Protect IMEI / Calibration Data.. llegue hasta aqui..

pero solo enciende en Recovery Mode, no entra en FTM ni EDL.

alguna idea..

[Zilre]

Amigo, si es 100% que no entra en FTM y EDL. Solo Jtag con alguna Box como Medusa PRO.

Deseo que alguien tenga algo mejor...